| |
G8MNY > TECH 25.03.19 09:04z 67 Lines 3154 Bytes #999 (0) @ WW
BID : 63492_GB7CIP
Read: GUEST
Subj: 70cms & 2m Dual Band Aerial
Path: HB9ON<IW2OHX<IR2UBX<IZ3LSV<IW0QNL<JH4XSY<JE7YGF<GB7CIP
Sent: 190325/0903Z @:GB7CIP.#32.GBR.EURO #:63492 [Caterham Surrey GBR]
From: G8MNY@GB7CIP.#32.GBR.EURO
To : TECH@WW
|
|
|
|
^ | 433mm
/ |
/ |
/ ______________________|
|||||______________________ 20mm
/ ^ 510mm ^ 86mm|
/ ^ |
/ feed point |
/ |
tower | 433mm
|
|
|
My prototype antenna was built using a single approx. 2.3 meter length of 4mm
stainless steel wire. This resulted in a totally self supporting ant. I much
prefer to see the least possible number of joins in a antenna so as the thing
ages you do not get crackles & other noise problems from your aerial.
In a similar manner the coax cable was soldered direct to the antenna at the
feed point which is some 86mm in from the antenna itself as shown above. (the
centre conductor goes to the top) I added some support by way of a 75mm length
of pvc tube 20mm diameter fitted between the wires on the tower side of the
feedpoint.
The coax runs through this tube. (the 20mm spacing is not critical but should
not be greater than 25mm for 70cm operation) The mounting to the tower can be
done in lots of ways.... my antenna is attached to a piping mast & I used a old
TV type boom to mast clamp & drilled 4mm holes straight through it at one end
in a manner so as when the 2.3 meter wire was run through the holes to it's
half way point & bent at right angles the horizontal part of the antenna is in
the position as shown above.
A couple of bolts at the other end (close to the sides of the wire..... A total
of 4 small bolts) resulted in a nice solid structure. Bend the wire as shown
above & trim to length as shown. The actual feed point is found by mounting the
antenna on some metal support & using a SWR meter as close to the feed point as
you can get. The length of the quarter wave stub (510mm measurement) is not
real critical so the 85mm dimension can be changed a little for minimum SWR.
(about 1.2 to 1 is easily found) Do your tuning on 70cm as it is more critical
on this band.
When the correct spot is found attach your feed line & seal it up. I soldered
the coax direct to the antenna. (you can't do this if you build the thing out
of aluminium!!) I tinned the 4mm wire at the feed point with aid of some
comweld 965 flux before soldering the cable on. I used coax-seal to seal the
cable. (if you must use silicon make sure that it is a neutral cure type.) Oh &
make sure you have a reasonable piece of coax cable for the length you are
going to use. (like if you are going to use, say, 20 meters of cable then you
need to find a low loss cable...... RG 213 is not the best to use & RG 58 is a
good dummy load at 70cm) The most expensive part of this project will be the
coax cable.
73 de Mike VK4XT
The antenna is not yet made by myself!
'73 de Roeland, PA0RBC@PI8SAT.#NH1.NLD.EU
Why Don't U send an interesting bul?
73 De John, G8MNY @ GB7CIP
Read previous mail | Read next mail
| |
