OpenBCM V1.08-3-g9b42 (Linux)

Packet Radio Mailbox

HB9ON

[OpenBCM Lugano JN46LA]

 Login: GUEST





  
G8MNY  > TECH     22.01.21 10:30z 100 Lines 4055 Bytes #999 (0) @ WW
BID : 20822_GB7CIP
Read: GUEST
Subj: Chopper Regulators
Path: HB9ON<IW2OHX<IQ2LB<IR2UFV<GB7CIP
Sent: 210122/1024Z @:GB7CIP.#32.GBR.EURO #:20822 [Caterham Surrey GBR]
From: G8MNY@GB7CIP.#32.GBR.EURO
To  : TECH@WW

By G8MNY                                        (Updated Jul 11)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)

These can either be step down voltage or step up voltage type, with the current
doing the inverse. Efficiency can be near to 100% in some applications.
Using an inductor to store energy they transform the power to what you want.

STEP DOWN REGULATORS
These are the most common type often from unregulated DC.

     FUSE  ==== L1
 24V>o-oÄ()))ÄÂÄÄÄÄÂÄÄÄÄÂÄÄÄÄRÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄ¿   L2      L3
550mA   INPUT ³    ³    ³   ÚÄÄÄÁÄÄÄÄÄÄ¿___³/e  ====    ====
       FILTER ³+   ³    ³   ³   I     d³ T1³\___())))ÄÂÄ()))ÄÂÄÄÄÄÂÄÄ>12V
             ===  ===   ÀÄÄÄ´+ Pulse   ³    _³_       ³      ³    ³    1A
              ³C1  ³C2      ³ Width IC ³    /_\D1    ===C3   ³   ===
              ³    ³   ÚÄÄÄÄ´c         ³     ³        ³   VOLTAGE ³C4
              ³    ³  === ÚÄ´r Osc    VÃÄÄÄÄÄ)ÄÄÄÄÄÄÄÄ)ÄÄÄÄ>POT   ³
              ³    ³ Co³  RoÀÄÄÄÄÄÂÄÄÄÄÙ     ³        ³      ³    ³
 0V >ÄÄÄÄÄÄÄÄÄÁÄÄÄÄÁÄÄÄÁÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÁÄÄÄÄÁÄÄ>

The main parts are L2, T1, D1 & C3. The controls IC may have T1 & D1 internal
depending of the power rating. The IC has an variable pulse width oscillator
inside that drives the transistor.

24VÄ´ .-----.
    ³ ³     ³     ³
12VÄ´-³     '-----'
    ³ ³
    ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
       T1 ON  OFF

 I  ³      .--.
    ³  _.-'    `-._
    ÀÄÁÄÄÄÄÄÄÄÄÄÄÄÄ

When T1 is on current builds up in L2, the R is a protection resistor to
monitor over current. When T1 turns off the energy stored in L2 rings down to a
high negative voltage that via D1 charges up C3. The voltage on C3/4 eventually
reaches the internal reference voltage in the IC via the voltage setting pot, &
this reduces the pulse width of T1's drive reducing the stored energy in L2.

Output current from L2 flows into the load when T1 is on & off, so current
addition occurs.

Due to the high current pulse nature of these systems input & output filters
are needed to keep these currents in the circuit & out of the external leads.


STEP UP REGULATOR
These are used alot nowadays in PCs with low voltage batteries.

   fuse  ==== L1             L2 ====           D1     ==== L3
12V>o-oÄÄ()))ÄÂÄÄÄÄÂÄÄÄÄÂÄÄÄÄÄÄ((((()ÄÄÄÄÄÄÄÂÄÄ´>ÃÄÄÂÄ()))ÄÂÄÄÄÄÂÄÄ> +24V 450mA
1A     INPUT  ³    ³    ³   ÚÄÄÄÄÄÄÄÄÄÄ¿    ³       ³      ³    ³ OUTPUT
       FILTER ³+   ³    ³   ³  Pulse   ³__³/ T1    +³      ³   +³ FILTER
             ===  ===   ÀÄÄÄ´+ Width  d³  ³\e      ===     ³   ===
              ³C1  ³C2      ³    IC   I³____³     C3³      ³    ³C4
              ³    ³   ÚÄÄÄÄ´c         ³    ³       ³   VOLTAGE ³
              ³    ³  === ÚÄ´r Osc    VÃÄÄÄÄ)ÄÄÄÄÄÄÄ)ÄÄÄÄ>POT   ³
              ³    ³ Co³  RoÀÄÄÄÄÄÂÄÄÄÄÙ    R       ³      ³    ³
 0V>ÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÁÄÄÄÁÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÁÄÄÄÄÁÄÄ>

The main parts are L2, T1, D1 & C3 as before. The controls IC may have T1 & D1
internal depending of the power rating. The IC has an variable pulse width
oscillator inside that drives the transistor (NPN here but could be VMOS FET
etc).

24vÄ´        .-----.
    ³  L2    ³     ³
12vÄ´-.      ³     ³
    ³ ³______³     ³__
    ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
       T1 ON  OFF
        In      Out
 I  ³      .- -.
    ³  _.-'  ³  `-..
    ÀÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄ

When T1 is on more current builds up in L2, the R is a protection resistor to
monitor over current in T1 (not the load!). When T1 turns off the energy stored
in L2 rings up to a high positive voltage that via D1 charges up C3. This
voltage eventually reaches the internal reference voltage in the IC via the
voltage setting pot, & this then reduces the pulse width of T1's drive reducing
the stored energy in L2 etc.

Output current to the load only flows when T1 is OFF, so current reduction
occurs.

Due to the high current pulse nature of these systems input & output filters
are needed to keep these currents in the circuit & out of the external leads.


Why don't U send an interesting bul?

73 de John G8MNY @ GB7CIP


Read previous mail | Read next mail


 29.03.2024 12:37:27zGo back Go up